A little signature. A lasting impression.Find your perfect fit ↓
The considered pour / A free sizing tool

The glass. The ice.
A mark that fits.

A cocktail starts with the right proportions. Match your glass to clear ice and a custom stamp, with room for every edge.

Glass, ice & stamp size calculator · Free · No signup

01 / Measure your pourMillimetre geometry
Your glass

Preset inches are approximate; calculations use millimetres. Measure the narrowest inside width where the ice will sit, especially with tapered glass.

82 mm / 3.23″ inner Ø
Your ice
Your service

Head diameter IDs are nominal. Fit checks use catalog envelopes of 38.1, 50.8 and 63.5 mm. Your workshop proof confirms final dimensions.

02 / The blueprintOne scale. Every layer.
Top-down geometry · 1 SVG unit = 1 mmMeasure before ordering
  • Glass inner rim
  • Ice footprint
  • Stamp head
  • Safe artwork zone

Choose your glass to calculate a fit.

Recommended ice dimension
52.3 mm cube side
Recommended stamp & price
38 mm · $69 brass base
Clearance & exact fit
Enable JavaScript for your fit calculation.

Ice dimensions are maximum custom-cut targets, rounded down to 0.1 mm. Do not round up to a larger mold. A smaller cube needs its flat-face stamp margin checked again.

Starting dwell: 2–3 seconds

Temper ice until frost clears. Use a dry room-temperature stamp and rehearse before service.

Custom-cut ice dimensions are rounded down to 0.1 mm; check your actual mold before using a standard size. The safe artwork circle is inset 4 mm inside the stamp, in addition to the 4 mm ice margin outside it. Estimates support a physical rehearsal.

01 / Leave room

Corners count.

A square cube’s diagonal is √2 × its side. We reserve 8 mm total clearance across the glass diameter, or 4 mm per opposing corner. A cube can wedge even when its side looks small enough.

02 / Keep an ice margin

A complete impression.

The whole stamp head stays inside a flat ice face with 4 mm left on each side. See the clear ice stamping guide for straight contact, tempering and dry-face technique.

03 / Rehearse service

Time the real pour.

Dwell is a starting estimate, not a guaranteed cycle time. Plan a rehearsal for your wedding bar or commercial service, including wiping and head recovery.

A few useful details

Before the
first impression.

How is glass clearance calculated?

For square ice, the diagonal is the side length multiplied by the square root of two. We reserve at least 8 mm total between that diagonal and the measured glass inner diameter: 4 mm at each opposing corner. Rectangular blocks use the full corner-to-corner diagonal. Measure the narrowest part of a tapered glass at the ice position.

Why does a 50 mm stamp not fit a 50 mm cube?

The full head needs a clean 4 mm ice margin on each side. Our nominal 50 mm option uses the catalog’s 50.8 mm physical envelope, so it needs a flat ice face at least 58.8 mm wide. The nominal 38 mm and 63 mm heads need at least 46.1 mm and 71.5 mm respectively. Confirm production dimensions in your workshop proof.

Can I stamp a clear ice sphere or a highball spear?

An uncut sphere has a curved surface and no safe flat stamping face. Cut and measure a stable flat face before choosing a head. A highball spear often has a top too narrow even for a 38 mm stamp; its height and glass taper also need a separate physical check.

How long should brass and stainless steel touch the ice?

Start with 2–3 seconds for lead-free bismuth brass or 4–5 seconds for 304 stainless steel. Temper ice for about 3–5 minutes until frost clears, use a dry room-temperature head, press lightly and lift vertically. These are starting estimates; rehearse with your actual ice, artwork and service conditions.

What does the recommended stamp cost?

Brass base prices are $69 for 1.5 inches (38 mm), $89 for 2.0 inches (50 mm) and $109 for 2.5 inches (63 mm). A 304 stainless steel head adds $15. An optional 304 steel handle adds $18 and an extra M8 interchangeable custom head adds $49. Prices are in USD; the calculator total includes only the selected head material.

Is this calculator free and private?

Yes. The calculator runs in your browser without signup, uploads or external dependencies, including when opened as a local file. It estimates geometry and technique; verify actual glass, ice and workshop dimensions before ordering.